![]() ![]() Note: Please refer to the GZ Media profile for the various runout combinationsĪdd a company: Pressed By - Decca Records Pressing Plant, Gloversville 82284E)Įxample: The Dils - 198 Seconds Of The Dils ![]() 109956H7/A) - since 1 January 2014Īdd a company: Pressed By - GZ Media + sequential number (e.g. #Xz/y (5 or 6 digits followed by a letter, digit/letter, e.g. Note: Please refer to the GZ Digital Media profile for the various runout combinations 54082E)Įxample: Jonathan Jeremiah - See (It Doesn't Bother Me) 90163H1/A) - between 20Īdd a company: Pressed By - GZ Digital Media + sequential number (e.g. #Xz/y (5 digits followed by a letter, digit/letter, e.g. PART ONE - LIST OF IDENTIFIED ETCHINGS / STAMPSĪdd a company: Mastered At - Iberofon, S.A. for ◇F: Lacquer Cut By - Bill Foster + ANV F). ◇F (symbol for the cutting room + letter of the engineer), and where the PAN is known, use an Alias or ANV without the symbol (e.g. => Discussion about "Symbol PAN" is found here.ġ5) Logos / logo types should be added in the runout strings as, e.g.ġ6) For combined identifiers with symbols, i.e. When in doubt about a symbol, inquire in this forum. They are added in theįormat "Lacquer Cut By plus the full name of the engineer" (Example: Symbols orĭrawn images such as ✩, ⚾, or ❀, ♀, etc., shall not be used, not even as ANVs. A good source is Copy Paste Characters (external link).ġ4) Only easily reproducible Unicode characters shall be used as engineer's PAN or ANVs. all caps, no pipes or separators, wide lettering).Ĥ) Please use ANVs or Aliases according to the Guidelines.ĥ) Don't include the studio / company as part of the signature or as ANV.Įxample: For " " or "BA-CR" credit "Björn Almstedt" + ANV "BA" as the engineer and "Cutting Room" as studio in the LCCN field.Ħ) For engineer credits derived from the runouts, use Lacquer Cut By (with some exceptions).Īny studio/company mentioned in an etching should be credited as Lacquer Cut At (with some exceptions).ħ) Direct Metal Mastering (DMM or similar) should be credited as Mastered By and Mastered At.Ĩ) Half-speed mastering credits shall be credited with Lacquer Cut By/ At.ĩ) Platers / metalworkers are credited with Plated By.ġ0) Plating / galvanization / metalworks companies are credited with Mastered At.ġ1) When unsure about the role use Mastered By / At.ġ2) Mastering credits on the cover and scribes in the runouts should both be credited.Įxample: Mastered By Bernie Grundman (cover) and BG in runouts = Mastered By - Bernie Grundman,Īnd Lacquer Cut By - Bernie Grundman + ANV BG.ġ3) Unicode symbols are allowed in the Matrix string when they closely represent the runout symbol. Not needed on the submission - just a point of reference.ġ) Searching for a string on page 1: Press CTRL (or STRG) and F and then enter the search string.Ģ) Do not split the runout strings up into stamped or etched parts - they should be left in one line.ģ) Please enter the runout strings as they appear (e.g. S, H or HS? Stamped, Hand-etched or Hand-etched ScriptĪdd a company: Lacquer Cut At / Mastered At / Pressed By / Manufactured By a company.Īdd a credit: Lacquer Cut By / Plated By / Mastered By an engineer. XXXXX: Identified part in the runout area This list is a culmination of all the other lists (see below for versions).īelow you will find names of cutting / mastering / plating engineers, studios, pressing plants and other manufacturing references. Welcome to the Master List of runout information - version 6
0 Comments
Leave a Reply. |